[ Pobierz całość w formacie PDF ]
SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00
www.cobra.it
NISSAN
MOD.
MICRA
YEAR.
03
fi
PETROL
DIESEL
X
MAKE
NOTE
For more clearness concerning the connectors marked M48, M49 and M50 it is suggested to
refer to the
fitting diagram nr. 182.
ALARM/SIREN
POSITION
Position the compact alarms and the sirens on the bulkhead that divides the engine
compartment and the passenger’s compartment. Pass the cables through the original rubber
sleeve near the driver’s side shock absorber.
CENTRAL UNIT POSITION
Position the modular systems and the modules under the panel covering the dashboard.
POWER SUPPLY
+ 30:
connect to the YELLOW wire at the position nr.79, in the connector marked M50,
coming out of the central marked BCM located under the panel covering the passenger’s
dashboard.
- 31:
connect to a ground terminal located behind the left lateral bulkhead.
IGNITION WIRE
+15/54:
Connect to the RED wire, at the position nr.78, in the connector marked M50,
coming out of the central marked BCM located under the panel covering the passenger’s side
dashboard.
DIRECTION INDICATORS
Connect to the PINK wire at the pos. nr. 65 and to the RED wire at the position nr. 66, in the
connector marked M50, coming out of the central marked BCM located under the panel
covering the passenger’s side dashboard.
ELECTRIC WINDOWS
Positive control signal
Front window, driver’s side:
Cut the YELLOW wire (positive on rise) in the wiring harness of the 16 way white connector,
directly coming out of the original push botton.
Front window, passenger’s side:
Cut the VIOLET wire (positive on rise), in the wiring harness coming out of the 10 way white
connector, directly coming out of the driver’s side door.
CENTRAL DOORS LOCKING
Negative control signal
Connect to the wires: GREEN at the position nr. 6 (lock) and to the BROWN at the position
nr.25 (unlock), located in the wiring harness coming out of the connector marked M48,
coming out of the central marked BCM, located under the panel covering the passenger’s side
dashboard.
IMMOBILISATION POINT
Fuel pump
Cut the 1,5 mm
2
GREEN wire (there are two GREEN wires, pls. verify the positive control of
the pump) in the wiring harness behind the instrument board, under the superior part of the
dashboard.
STARTER
+50:
Cut the WHITE wire, in the 6 way connector, in the ignition key.
BONNET SWITCH
Install an additional switch on the front headlamp support plate, passenger’s side.
DOORS SWITCH
Connect to the wires: BLUE position nr.29 ( ant. driver’s side), GREEN position nr. 30 (ant.
passenger’s side) in the connector marked M48 coming out of the central marked BCM,
located under the panel covering the dashboard passenger’s side and to the wires: BLUE
position nr.59 (post. driver’s side), GREEN position nr.60 (post. passenger’s side) located in
the connector marked M49 coming out of the central BCM, located under the panel covering
the passenger’s side dashboard.
BOOT SWITCH
Connect to the ORANGE wire, at the position nr.10, in the connector marked M48, coming
out of the central marked BCM, located under the panel covering the passenger’s side
dashboard.
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed
as per the instructions given on the product installation manual.
nimic03gbb.doc
SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00
www.cobra.it
FITTING DIAGRAM NR.182
Connectors disposition on the central marked BCM,
located under the covering of the passenger’s side dashboard
Black connector in White connector in superior
vertical position horizontal position
73 79
M 50
52 41
M 49
64 53
White connector in lower
65 74 horizontal position
21 40
M 48
1 20
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed
as per the instructions given on the product installation manual.
nimic03gbb.doc
[ Pobierz całość w formacie PDF ]